৳600 বা তার বেশি অর্ডারে Steadfast কুরিয়ার ডেলিভারি চার্জ মাত্র ৳85। অর্ডার কনফার্ম হবার পরের দিন কুরিয়ারে শিপ করা হবে। কুরিয়ারে ডেলিভারি হতে সাধারণত 2–4 দিন এবং পোস্ট অফিসে 2–5 কর্মদিবস লাগতে পারে। --

৳600 বা তার বেশি অর্ডারে কুরিয়ার ডেলিভারি চার্জ মাত্র ৳85।

অর্ডার কনফার্ম হবার পরের দিন কুরিয়ারে শিপ করা হবে। কুরিয়ারে ডেলিভারি হতে সাধারণত 2–4 দিন এবং পোস্ট অফিসে 2–5 কর্মদিসব লাগতে পারে।

CH32V003F4P6 32-Bit RISC-V Microcontroller Development Board (USB Type-C)

Ultra-low-cost, 48 MHz 32-bit RISC-V microcontroller development board based on the WCH CH32V003F4P6 (TSSOP-20). Features a USB Type-C power port, 3.3V/5V logic level selection jumper, onboard user LED, and Arduino IDE / PlatformIO compatibility—ideal for replacing 8-bit ATtiny/STM8 chips in compact IoT and embedded projects.
Old price: 270.00৳
150.00৳
Ship to
*
*
Shipping Method
Name
Estimated Delivery
Price
No shipping options

Overview

The CH32V003F4P6 Development Board brings modern 32-bit RISC-V performance to ultra-low-cost embedded applications. Powered by the WCH QingKe V2A 32-bit processor running up to 48 MHz, this compact breadboard-friendly board is an ideal upgrade over traditional 8-bit microcontrollers like the ATtiny85 or STM8S003.

Equipped with a modern USB Type-C port for power, a selectable 3.3V / 5V operating voltage jumper, an onboard programmable LED, and full header pin breakouts, it is ready for rapid prototyping right out of the box.

Key Features

  • High-Efficiency 32-Bit RISC-V Core: QingKe V2A (RV32EC) architecture clocked up to 48 MHz with single-cycle multiplication and hardware division.
  • Wide Operating Voltage (3.3V & 5V): Built-in onboard voltage regulator with a hardware jumper to switch logic levels seamlessly between 3.3V and 5V sensors.
  • Rich Peripheral Set: Includes 10-bit ADC, hardware SPI, I2C, USART, 16-bit advanced/general-purpose timers, built-in Op-Amp/Comparator, and 7-channel DMA.
  • Single-Wire Debug (SWIO): Easy programming and debugging via the 1-wire SWIO interface using a WCH-LinkE programmer.
  • Developer-Friendly Toolchains: Fully supported in the Arduino IDE (via ch32v003duino), PlatformIO, and WCH MounRiver Studio.

Technical Specifications

Microcontroller WCH CH32V003F4P6 (TSSOP-20 Package)
Core Architecture 32-Bit RISC-V QingKe V2A (RV32EC)
Max Clock Speed 48 MHz
Flash Memory 16 KB CodeFlash + 1920 B Bootloader
SRAM 2 KB
Operating Voltage 3.3V or 5V (Selectable via Onboard Jumper)
Power Interface USB Type-C (Power Only) / VCC Pin
GPIO Pins 18 I/O Pins (with External Interrupt Support)
ADC 1x 10-Bit ADC (8 External Channels)
Communication Interfaces 1x USART, 1x I2C, 1x SPI
Timers & Analog 1x 16-bit Advanced Timer, 1x 16-bit GP Timer, 2x Watchdogs, 1x Op-Amp / Comparator
Programming Interface SWIO (Single-Wire Debug via PC1)
Onboard Indicators Power LED + User Programmable LED (Connected to PC0)

Pinout & Programming Notes

Function / Peripheral Pin Assignment Notes
Programming (SWIO) PC1 (SWDIO) Requires WCH-LinkE programmer (USB-C port is for power only)
Onboard User LED PC0 Active-High / Active-Low depending on board revision
USART (TX / RX) PD5 (TX) / PD6 (RX) Default hardware serial pins
I2C (SDA / SCL) PC1 (SDA) / PC2 (SCL) Note: PC1 is shared with SWIO; disconnect programmer during I2C use
SPI (SCK / MISO / MOSI) PC5 / PC7 / PC6 Hardware SPI interface
External Crystal PA1 / PA2 Optional 24 MHz HSE (internal 24 MHz HSI + PLL used by default)

Note: The onboard USB Type-C connector provides 5V power to the board only and does not support direct USB data programming. You will need a WCH-LinkE debugger/programmer connected to the 3V3, GND, and SWIO pins to upload firmware.

Package Includes

  • 1x CH32V003F4P6 RISC-V Development Board
  • 2x 10-Pin Male Header Strips (Unsoldered)
Only registered users can write reviews
You have no items in your shopping cart.